Communication

Heat, sound, water and fire insulated stucco in a single product.

Trust & Dignity
NanomixKF-S 011
STUCCO

Heat, sound, water and fire insulated stucco in a single product

It is a multi-purpose and single-component insulating plaster produced in white color in A1 fire-proof class with the feature of high diffusion (breathability) ensuring insulation of buildings against heat, sound, water and fire thanks to the inorganic natural aggregates contained by it and high technology used and applied on facades.

APPLICATION SURFACES
Brick, Exposed Concrete, Concrete, Gas concrete, pumice

20 kg. Kraft BagType of Package

White Granule PowderAppearance

333+-%10(kg/m3)Dry Density

T1Heat Conductivity

25 DbSound Insulation

1,638 (N/mm2) CSIIPressure Resistance

0,319 (N/mm2)Bond Strength

0,312 (kg/m'min 0.5) W1Water Absorption

(1000C°)Fire Resistance

48 HoursPeriod for being ready for dye

16 MonthsShelf Life

between +5C° +35C°Application Temperature Range

Machine or Steel TrowelForm of Application

11 cm/m2 approximately 4,5 / 5 kg.Consumption

AREAS OF USE

It is directly applied on all wall surfaces including load-bearing systems on facades of buildings (rough or finish coat, brick, gas concrete, pumice block, concrete surfaces, briquette etc.). It does not need extra adhesion agents. It is possible to obtain a great variety of decorative surfaces.

It is easily applied to insulation and alteration of buildings currently occupied in addition to its application to rough constructions. In such applications, it is recommended to apply by making surfaces free from dye, mineral coat and similar materials producing a film layer on the surface at the level of minimum 70%.

POINTS TO PAY ATTENTION

The product must be mixed by a mixer or concrete mixer (for minimum 6 minutes).

When KF-S 011 is mixed, it must not be mixed with water more than the specified measure (15 lt).

If the plaster prepared with KF-S 011 is kept in the bowl longer for any reason and the plaster’s consistency is lost, water must not be added again. Rather, the consistency may be renewed by remixing by a low cycle mixer.

PREPARATION OF PLASTER

A bag of KF-S 011 stucco is poured in a clean bowl. Approximately 15 liters of water are added and it is mixed by a low cycle mixer for 6-7 minutes.

HOW TO APPLY?

The surfaces to be applied must be made free from dust, dirt and similar factors. After the façade is taken to the scales in the desired thickness with ano and net edge angle beads, the previously prepared ano and bead spaces are filled and finished by a machine or trowel and thus the first stage is completed. KF-S 011 shall be prepared for finishing after 4 hours approximately.

In the second stage, KF-S 011 is applied on the ready finished surface as a layer in 0.5 cm thickness by a trowel. KF-S 011 application is completed by using tools appropriate for the decorative surface options to be preferred (steel trowel, types of clover, roll, sponge etc.).

Dye may be applied 48 hours after completion of KF-S 011 stucco application and there is no drawback for all kinds of decorative processes applied on jamb and precast plaster, in short sand plaster.

NanomixKF-S 020
INTERIOR WALL PLASTER

Heat, sound, water and fire insulated stucco in a single product

KF-S 020 interior wall plaster is a high-resistant plaster product which does not required further plaster on interior walls in addition to heat, sound and fire insulation. It is produced in white or grey preferably. It is not deformed in possible leakage or humidity formations due to its water-resistant feature due to absence of direct exposure to water on interior walls in addition to its long life. It is a breathable building and insulation material in class A1 and of fireproof nature in economic and practical application.

SURFACE OF APPLICATION
Brick, exposed concrete, concrete, gas concrete, pumice

20 kg. Strength BagType of Package

White Granule PowderAppearance

380+-%10(kg/m3)Dry Density

T1Heat Conductivity

25 DbSound Insulation

1,67 (N/mm2) CSIIPressure Resistance

0,368 (N/mm2)Bond Strength

(1000C°)Fire Resistance

48 HoursPeriod for being ready for dye

16 MonthsShelf Life

between +5C° +35C°Application Temperature Range

Machine or Steel TrowelForm of Application

1 cm/m2 approximately 4,5 / 5 kg.Consumption

AREAS OF USE

Insulation of living areas with KF-S 020 interior wall insulating plaster on interior walls against loss of heat especially substantially prevents effect of the other building elements used in the building (wall, column, beam etc.) on the ambient temperature by absorbing temperature. As a result of this effect, high percentage of saving may be achieved in energy use only by heating or cooling the air inside, heating and cooling shall be achieved very faster in the interior environment in winter and summer respectively.

Staining and dyeing process may be performed 40 hours after its application optionally. It is possible to get a great variety of decorative surfaces. (use of water-based dyes is recommended to prevent loss of breathability feature.)

POINTS TO PAY ATTENTION

1 bag of KF-S 020 must be fully used when it is opened due to its contents.

The product must be mixed by a mixer or concrete mixer (for minimum 6 minutes).

When KF-S 020 interior wall plaster is mixed, it must not be mixed water more than the specified measure (15 lt).

If the plaster prepared with KF-S 020 is kept in the bowl longer for any reason and the plaster’s consistency is lost, water must not be added again. Rather, the consistency may be renewed by remixing by a low cycle mixer.

PREPARATION OF PLASTER

A bag of KF-S 020 interior wall plaster is poured in a clean bowl. Approximately 15 liters of water are added and it is mixed by a low cycle mixer for 6-7 minutes.

HOW TO APPLY?

The surfaces to be applied must be made free from dust, dirt and similar factors. After the façade is taken to the scales in the desired thickness with ano and net edge angle beads, the previously prepared ano and bead spaces are filled and finished by a machine or trowel and thus the first stage is completed. KF-S 020 shall be prepared for finishing after 4 hours approximately.

In the second stage, KF-S 020 is applied on the ready finished surface as a layer in 0.5 cm thickness by a trowel. KF-S 011 / KF-S 020 application is completed by using tools appropriate for the decorative surface options to be preferred (steel trowel, types of clover, roll, sponge etc.).

Satin, dye, stropiyer, drywall and similar optional applications may be performed 48 hours after completion of KF-S 020 interior wall plaster application.

OUR BRANDS
Close